Авторизация

Забыли пароль?

Коды ошибок hp designjet 700, designjet 750c, designjet 755cm

CodeDescriptionRemedy
10001Window sensor circuitry not operating correctly.Check window sensor switch. Check that the sensor cable is connected to the front panel PCA.
10011Bail sensor indicates the bail is up when it should be down.Use the bail sensor test to help troubleshoot.
10012Bail sensor indicates the bail is down when it should be up.Use the bail sensor test to help troubleshoot. Check for a sticky sensor flag.
10013Bail is falling down (missing the detent).Check for Mechanical problems. Perform the Bail Calibration.
10020ROM test failure.Replace EPROMs. Replace main PCA.
10021DRAM test failure.Replace main PCA.
10022Swath RAM test failure.Replace main PCA.
10023EEROM test failure.Replace EEROM. Replace main PCA.
10024Pen interface ASIC test failure.Replace main PCA.
10025Communication failure between the main and servo processors. Communication occurs through the processor support ASIC.Replace main PCA.
10026Servo interrupts not occurring or not reaching the mainprocessor through the processor support ASIC.Replace main PCA.
10027Error inservo drive calculations.Replace main PCA.
10028Error inEEROM checksum calculations.Replace or clear EEROM. Replace mainPCA. Perform all calibrations. Press Enter to temporarily clear.
10029Error inEEROM write.Replace or clear EEROM. Replace mainPCA. Perform all calibrations.
01002aRS-232-C loopback test failure.Replace main PCA.
01002bCentronics test failure.Replace main PCA.
01002cServo processor communication error.Replace main PCA.
01002fDRAM test failure.Replace main PCA.
010030, 010031Failed communications betweenthe carriage and mainprocessors.For all OlOO3X codes, check trailing cable connections and continuity. If needed, replace the main PCA or the carriage assembly.
10032Carriage ASIC test failure.Refer to 010030.
10033Pen interface ASIC and carriage ASIC link test failure.Refer to 010030.
10040Error detected in X-axis servo feedback loop.Check X-encoder, encoder cable, main PCA.
10041Error detected in Y-axis servo feedback loop.Check encoder strip, carriage assembly, trailing cable, main PCA.
10050Uppermost SIMM indicates a failure.Replace uppermost SIMM.
10051Next to uppermost SIMM indicates a failure.Replace next to uppermost SIMM.
10052Both upper and lower SIMMs indicate a failure.Replace both upper and lower SIMMs.
10080RS-232-C data overflow.Data byte was not read before another was entered into the UART. Replace main PCA. If problem remains report the firmware problem to the HP Response Center or the nearest HP Sales and Support Office.
020001, 020002Firmware problem. Bad EPROMS.For all 2XXXX errors, report the firmware problem to the HP Response Center or the nearest HP Sales and Support Office. Note conditions before the error occurred. Include system configuration in the report.
30000X-axis shutdown.All 300XX errors indicate a failure of hardware or electronics of the X- or Y-Axis. Refer to SERVO CONTROL SYSTEM FAILURES in this chapter.
30001Y-axis shutdown..Refer to code 030000.
30002Y-axis friction too highRefer to code 030000.
30003Y-axis failureRefer to code 030000.
30010Excess friction in pen capping assemblyCheck mechanical parts in pen capping assembly for binding.
04xxxxMIO interface error.If an MIO is installed, check the MIO setup. Then replace the MIO.
05xxxxPlotter system errors found.MIO problem is indicated. The most likely cause is the main PCA or the interconnect PCA. Replace the interconnect PCA. Replace the main PCA.
60111Line sensor LED not bright enough.The optical sensor on the carriage has failed to locate lines drawn during the pen calibration routine. Reduce the ambient light. If the media is not clean and reflective, change the media. If the lines are faint, replace the pens. Clean lenses. Replace LED. Use the Edge detect test, found in the service menu, to help troubleshoot.
60302Large final residual correction.Refer to code 060111.
0700xxCould not calibrate for the drop detect sensor location.Check that the sensor and the sensor drop detect sensor location. housing are properly aligned. Check that the service station cover is correctly seated over the sensor housing. Check that the sensor housing opening is clear of obstructions. Use the Pen nozzle and Drop detect tests, found in the service menu, to help troubleshoot. Use the Drop detect calibration, found in the service menu to recalibrate the position of the sensor. Check the drop sense cable connections. Replace the drop sensor.
0f0000Firmware error.Notify the HP Response Center or the nearest HP Sales and Support Office.


Фотография 1 Фотография 1 Фотография 2 Фотография 3 Фотография 4 Фотография 1 Фотография 2 Фотография 3

Выравнивание по центру

196084, г. Санкт-Петербург, Московский проспект, дом 136 корпус 2 литера А, тел. 8(812) 967-25-21, 8(812) 967-25-31, info@andyshop.ru

Эндишоп.ру - это онлайн магазин доставки по России более 20000 товаров и услуг для обслуживания и бесперебойной работы оргтехники. У нас можно заказать любые расходные материалы, опции, блоки и отдельные запчасти принтеров и картриджей марки: brother, canon, duplo, epson, hp, konica minolta, kyocera mita, lexmark, oki, panasonic, philips, ricoh, samsung, riso, sharp, toshiba, xerox. Срок отправки и поставки большинства товаров и услуг регулируются только выбранной Вами формой оплаты. Мы предлагаем качественные, сертифицированные для России и полностью совместимые аналоги boost, g&g, hi-black, katun, static control, uninet и даем гарантию на все продаваемые нами товары и услуги. Вы всегда можете получить ответ на свой вопрос и больше информации задав вопрос нашему онлайн-консультанту на сайте. Информация, указанная на сайте носит информационный характер и не является публичной офертой, нашей офертой является подтверждение заказа с указанием товара, сроков поставки и его цены.

Создание Интернет-магазина Andyshop.ru - PHPShop. Все права защищены © 2003-2018.