| Code | Description |
| 0000D8 | Library Error. |
| 10020 | The Checksum read on the Flash SIMM is incorrect. |
| 10021 | The baseDRAM or theRAM SIMM tests failed. |
| 10022 | The SWATH RAM test failed. |
| 10023 | A fuse on the Main PCA has blown. |
| 10024 | Problem initializingthe encoder pulse generator. |
| 10030 | One of the two interconnect boards not detected. |
| 10031 | The Printhead Primitive Driver ASIC Test Failed. |
| 10032 | Fan Test Failed -Current not detected in one or bothfans. Error data (XX): 1 -Electronics Module fan not running. 2 -Service station fan not running. 3 -Bothfans not running. 10 -Electronics Module fan is short-circuited. 20 -Service Station fan is short-circuited. 30 -Bothfans are short-circuited. 12 -Service Station fan is not running and the Electronics Module fan is short-circuited. 21 -Electronics Module fan is not running and the Service Station fan is short-circuited. |
| 10033 | The DC Motor Driver ASIC Test Failed. |
| 10034 | One of the DC Motors has failed. Error data: 00010000 -Y-axis Motor Failed. 00020000 -X-axis Motor Failed. 00030000 -Both DC Motors Failed. |
| 10035 | One of the Stepper Motors has failed. Error data (oXABCDEF): If the value of each letter is o, then the component is OK. If the value of each letter is different from 0 then the component has failed. X -Electronics signal failed (ignore other values). A -Elevator Stepper Motor Failed. B -Refill Stepper Motor Failed. C -Primer Stepper Motor Failed. D -Service station (Z-axis) Stepper Motor Failed. E -Service station (X-axis) Stepper Motor Failed. F -Bail Stepper Motor Failed. |
| 10036 | ADC Test Failure in the Main PCA A short circuit in the Y/X-axis or ANY stepper motor. This short circuit is causing some of the fuses in the Electronics Module to burn. Error data: 00000800 -Problem with the Y-axis. 00001000 -Problem with the X-axis. |
| 10037 | ADC Test Failure in the Carriage PCA. |
| 10038 | A Printhead voltage could not be set -Main PCA Failure. |
| 10039 | A Printhead voltage could not be set -Carriage PCA Failure |
| 10040 | The Ambient Temperature measured is out of the normal range. |
| 10042 | The status of one of the opticalsensors is not stable when it should be. Error data (X): 0 -Problem with the Media Sensor. 1 -Problem with the Pinch-arm Sensor. 2 -Problem with the Refill Assembly Sensor. 3 -Problem with the Elevator Sensor. 4 -Problem with the Service Station Sensor. 5 -Problem with the Primer Sensor. |
| 10043 | Problem with theCarriageBoard. |
| 10100 | Error reading the EEROM. |
| 10101 | An action outside the EEROM limits has been performed. |
| 10102 | Physical EEROM write and/or write operations failed. The EEROM data that is written does not match the data that is read. |
| 10110 | The content of the permanent configuration area of theEEROM is not valid when theprinter is initialized in Service Mode. |
| 10111 | The content of the User configuration area of the EEROM is not valid when the printer is initialized. |
| 10120 | The content of the permanent configuration area of the EEROM is not valid when the printer is initialized in Normal Mode. |
| 10121 | One of the banks of the user area was corrupted while writing or reading in that area. |
| 20000 | Error in finding the Primer home position. |
| 20001 | Error in finding the Elevator home position. |
| 20002 | Error in finding the Refill Arm home position. |
| 20003 | Error in finding the Refill Stepper Motor home position. |
| 20004 | Error in finding the Service Station home position. |
| 20005 | Elevator has problem reaching a desired position. |
| 20006 | The refill position in the Y-axis is not calibrated. |
| 20010 | Problem with fine movement of the Y-axis motor. |
| 20011 | Error during initialization of the Y-axis. |
| 40601 | The MIO card does not support the MIO 6 protocol. Cards with version 5 or below can not be used with this plotter. Version 5.1 cards behave as expected but do not support PML instructions. Install the latest version. |
| 040xxx | MIO Card Error |
| 50000 | The Line Sensor has problems finding the Mark Encoder. |
| 60000 | The Line Sensor is not functioning properly because there is too much ambient light. |
| 60100 | Incorrect Line Sensor type in the EEROM. |
| 60200 | Incompatible Firmware and Carriage PCA. |
| 60300 | Incompatible Firmware and Line Sensor. |
| 60400 | Incompatible Carriage PCA and Line Sensor OR Line Sensor not calibrated after replacing Carriage Assembly. |
| 60500 | Line Sensor not calibrated. |
| 07xxxx | Firmware Error. |
| 80001 | Hard Disk Drive installed without PostScript. |
| 08xxxx | PostScript Error. |
| 90004 | PostScript installed without the Hard Disk Drive. |
| 09xxxx | Hard Disk Drive Error. |
Картриджи принтера
Заправка картриджей
Ремонт принтера
Запчасти принтера
Купим картридж, принтер, бумагу а4 
