Code | Description |
0000D8 | Library Error. |
10020 | The Checksum read on the Flash SIMM is incorrect. |
10021 | The baseDRAM or theRAM SIMM tests failed. |
10022 | The SWATH RAM test failed. |
10023 | A fuse on the Main PCA has blown. |
10024 | Problem initializingthe encoder pulse generator. |
10030 | One of the two interconnect boards not detected. |
10031 | The Printhead Primitive Driver ASIC Test Failed. |
10032 | Fan Test Failed -Current not detected in one or bothfans. Error data (XX): 1 -Electronics Module fan not running. 2 -Service station fan not running. 3 -Bothfans not running. 10 -Electronics Module fan is short-circuited. 20 -Service Station fan is short-circuited. 30 -Bothfans are short-circuited. 12 -Service Station fan is not running and the Electronics Module fan is short-circuited. 21 -Electronics Module fan is not running and the Service Station fan is short-circuited. |
10033 | The DC Motor Driver ASIC Test Failed. |
10034 | One of the DC Motors has failed. Error data: 00010000 -Y-axis Motor Failed. 00020000 -X-axis Motor Failed. 00030000 -Both DC Motors Failed. |
10035 | One of the Stepper Motors has failed. Error data (oXABCDEF): If the value of each letter is o, then the component is OK. If the value of each letter is different from 0 then the component has failed. X -Electronics signal failed (ignore other values). A -Elevator Stepper Motor Failed. B -Refill Stepper Motor Failed. C -Primer Stepper Motor Failed. D -Service station (Z-axis) Stepper Motor Failed. E -Service station (X-axis) Stepper Motor Failed. F -Bail Stepper Motor Failed. |
10036 | ADC Test Failure in the Main PCA A short circuit in the Y/X-axis or ANY stepper motor. This short circuit is causing some of the fuses in the Electronics Module to burn. Error data: 00000800 -Problem with the Y-axis. 00001000 -Problem with the X-axis. |
10037 | ADC Test Failure in the Carriage PCA. |
10038 | A Printhead voltage could not be set -Main PCA Failure. |
10039 | A Printhead voltage could not be set -Carriage PCA Failure |
10040 | The Ambient Temperature measured is out of the normal range. |
10042 | The status of one of the opticalsensors is not stable when it should be. Error data (X): 0 -Problem with the Media Sensor. 1 -Problem with the Pinch-arm Sensor. 2 -Problem with the Refill Assembly Sensor. 3 -Problem with the Elevator Sensor. 4 -Problem with the Service Station Sensor. 5 -Problem with the Primer Sensor. |
10043 | Problem with theCarriageBoard. |
10100 | Error reading the EEROM. |
10101 | An action outside the EEROM limits has been performed. |
10102 | Physical EEROM write and/or write operations failed. The EEROM data that is written does not match the data that is read. |
10110 | The content of the permanent configuration area of theEEROM is not valid when theprinter is initialized in Service Mode. |
10111 | The content of the User configuration area of the EEROM is not valid when the printer is initialized. |
10120 | The content of the permanent configuration area of the EEROM is not valid when the printer is initialized in Normal Mode. |
10121 | One of the banks of the user area was corrupted while writing or reading in that area. |
20000 | Error in finding the Primer home position. |
20001 | Error in finding the Elevator home position. |
20002 | Error in finding the Refill Arm home position. |
20003 | Error in finding the Refill Stepper Motor home position. |
20004 | Error in finding the Service Station home position. |
20005 | Elevator has problem reaching a desired position. |
20006 | The refill position in the Y-axis is not calibrated. |
20010 | Problem with fine movement of the Y-axis motor. |
20011 | Error during initialization of the Y-axis. |
40601 | The MIO card does not support the MIO 6 protocol. Cards with version 5 or below can not be used with this plotter. Version 5.1 cards behave as expected but do not support PML instructions. Install the latest version. |
040xxx | MIO Card Error |
50000 | The Line Sensor has problems finding the Mark Encoder. |
60000 | The Line Sensor is not functioning properly because there is too much ambient light. |
60100 | Incorrect Line Sensor type in the EEROM. |
60200 | Incompatible Firmware and Carriage PCA. |
60300 | Incompatible Firmware and Line Sensor. |
60400 | Incompatible Carriage PCA and Line Sensor OR Line Sensor not calibrated after replacing Carriage Assembly. |
60500 | Line Sensor not calibrated. |
07xxxx | Firmware Error. |
80001 | Hard Disk Drive installed without PostScript. |
08xxxx | PostScript Error. |
90004 | PostScript installed without the Hard Disk Drive. |
09xxxx | Hard Disk Drive Error. |