Назад

CodeDescription
01.0:03Error impact I2C channel.
01.0:10Problem with the Gamut PCI PCA.
01.1:10Problem with the PrintMech PCA.
01.2:10ISS PCA faulty - Humidity sensor out of scale or NVM backup failure.
02.1:10Problem with the Carriage PCA.
2:10Encoder seems to be wrong.
3:10Problem with the Power Supply Unit.
05.1:10CPU Fan is stopped or burnt.
05.3:10Main memory size failure.
6:03NVM file has bad CRC.
6:10Main NVM failure - not detected, read/write failed or readback error.
7:107:10
8:11Problem with the Front Panel.
11:10Trailing Cable does not seem to be detected.
13.n:10Problem starting acumen supplies.
21:03Service Station servo shutdown.
21:12Fail moving Service Station.
21:13Problem with the Service Station.
23:10Problem with the APS.
24:03:00Ink Setup failure (Ink Supply Tubes purge failed).
24:10:00Broken bag detected in Ink Cartridge.
26.0:01Bad contact detected in ISS slot0 floater.
26.1:01Bad contact detected in ISS slot1 floater.
26.2:01Bad contact detected in ISS slot2 floater.
26.3:01Bad contact detected in ISS slot3 floater.
26.n:10Order of Ink Supplies incorrect.
26:14:00A wrong Ink Cartridge has been detected.
27:03:00An error has occurred in Printhead detection.
27:14:00A wrong Printhead has been detected.
29.0:01Printhead Cleaner not inserted correctly in slot 1.
29.1:01Printhead Cleaner not inserted correctly in slot 2.
29.2:01Printhead Cleaner not inserted correctly in slot 3.
29.3:01Printhead Cleaner not inserted correctly in slot 4.
29.4:01Printhead Cleaner not inserted correctly in slot 5.
29.5:01Printhead Cleaner not inserted correctly in slot 6.
29.6:01Printhead Cleaner not inserted correctly in slot 7.
29.7:01Printhead Cleaner not inserted correctly in slot 8.
41:03:00Electrical current limit in Media-Axis Motor.
41:10:00Electrical fault in Media-Axis Motor.
42:03:00Electrical current limit in Scan-Axis Motor.
42:10:00Electrical fault in Scan-Axis Motor.
43:10:00Vacuum Fan has stopped functioning.
44:10:00Problem with the Aerosol Fan.
44:11:00Aerosol Fan not connected.
51.1:10PHC Access Door Sensor failure.
51:10:00Window Sensor failure.
52:10:00Drop Detector switch On/Off failure.
53:10:00Media Sensor failure.
54:10:00Media Lever Sensor failure.
55:10:00Problem with the Line Sensor.
56:03:00Analog Encoder calibration failed.
56:10:00Analog Encoder calibration failed.
61:01:00The file format is incorrect and the Printer cannot process the job.
61:04.1The Postscript fonts are missing. Upgrading the Firmware will re-install the fonts.
61:08.1The file cannot be printed because it is password protected.
63:04:00Input/Output problem through the Network Card.
64:04:00Input/Output problem through the USB Port.
65:04:00Input/Output problem through an unknown port.
66:08:00Cannot print file on current paper type. The paper type has changed since the file was sent, so the file cannot be printed on the paper type currently loaded.
67:04:00Input/Output problem through an Firewire Port.
68:03:00Non-critical permanent data was lost. This does not prevent the Printer to work, only that internal life counters will not be recorded until the Printer is restarted.
71:03:00Out of memory failure.
71:04:00Out of memory failure.
71:19:00Default Serial Number found in the main and backup NVM. It seems that both the Ink Supply Tubes and Hard Disk Drive have been replaced together.
72:04:00Generic Firmware error.
73:03:00Servo Error.
74:00:00Failed getting Part Number/Serial Number.
74:01:00Error uploading firmware update file.
74:04:00Old Vacuum Fan detected - upgrade the Firmware.
76:03:00Out of Disk space - Data was lost.
77:04:00Embedded Web Server internal software error.
79.1:04CDS server lost connection with client.
79:03:00Generic Firmware error.
79:04:00Generic Firmware error.
81:01:00Paper servo shutdown.
81:03:00It was impossible to correctly stop the servo before setting the encoder position.
81:10:00Fail starting Paper Motor.
85:03:00Problem finding the Drive Roller zero.
86:01:00Carriage servo shutdown.
86:03:00Scan-Axis length test failure.
86:10:00Initializing Scan-Axis Motor failure.
86:11:00Scan-Axis length too short.
91:02:00The HP Instant Support troubleshooting tool has detected that at least one Printhead has been replaced without having a specific error, and without being recovered/cleaned.
91:10:00The HP Instant Support troubleshooting tool has detected that at least, for one Printhead: It is currently in warranty (less than 1000cc of ink used). That the previous 2 Printheads had been found defective within the warranty period.
93:11:00Unable to pressurize the IDS.
98:02:00Switching to lower performance due to Printhead quality.

Наверх
  • Яндекс.Метрика
    Создание интернет-магазина Andyshop.ru - PHPShop. Все права защищены © 2004-2024.