Назад

CodeDescription
0001Internal RAM
The read/write of the RAM on the Main PCA was diagnosed and an error was detected.
0002SRAM
The read/write of the SRAM on the Main PCA was diagnosed and an error was detected.
0004Flash ROM
The program area in the Flash ROM is sum-checked, and it could not be read, causing an error.
0008PIO
The read/write of a specific Parallel I/O (PIO) was tested and an error was detected.
0010NVRAM
Problems with the NVRAM detected.
0020FPGA (Main PCA)
The read/write of the FPGA-ATG (Band Memory) and FPGA-RSM (Mask Memory) registers on the Main PCA was diagnosed and an error was detected.
0040FPGA (Carriage PCA)
The read/write of the FPGA-PTC (Print Timing Controller) and FPGA-PDD (Print Data Distributor) registers on the Carriage PCA was diagnosed and an error was detected.
0080ASIC CONF (Main PCA)
The program load from the Flash ROM on the Main PCA to the FPGA on the Main PCA or sum-check was not performed correctly and an error occurred.
0100ASIC CONF (Carriage PCA)
The program load from the Flash ROM on the Main PCA to the ASIC on the Carriage PCA or sum-check was not performed correctly and an error occurred.
0200DRAM
The read/write of the image band memory on the Main PCA was diagnosed and an error was detected
0400USB Register
The read/write of the USB controller on the Main PCA was diagnosed and an error was detected.
0800Power Supply (+36V, +24V, +12V)
The power supplies of +36, +24 and +12 V were diagnosed and could not be detected.
1110GA_ATG Block Clear Error
The ATG band memory block erase does not end. This error is checked during Boot-Up sequence and printing.
1111GA_ATG DMA Transfer Error
There is a problem in the data path. This error is checked during printing.
112xVacuum Fan Error x = 0: The Vacuum Fan (Wiping Side) has failed. x = 1: The Vacuum Fan (Center of the Platen) has failed. x = 2: The Vacuum Fan (Capping Side) has failed.
1140Flash ROM Write Error
A time-out error occurs when the NVRAM contents are being saved in the flash memory in Maintenance Mode and erasing does not end.
1150Home Position Sensor Error
The Carriage cannot be moved to it’s home position.
1160Wiping Error
When the Wiping Motor has been running for a while, the sensor fails to detect that the Motor has made one turn.
1170Temperature Sensor Error
The Temperature Sensor detects abnormal temperatures (-10C or lower or 85C or higher).
1180Capping Motor Error
Capping Motor over current is detected.
119xHead Relay Variable Supply Error
Output voltages of the Head Relay Board are abnormal.
11AxNVRAM Error
The data in the NVRAM is incorrect.
11C0Cap Position Error
The Carriage position sensors have detected more than a 2mm gap during the capping operation.
11D0Cooling Fan Error
When the Printhead temperature reaches above 43C, the Printer will check whether the temperature drops below 43C during printing. This error will appear if the temperature does not drop below 43C after 10 minutes.
1,10E+01Long Term Storage Error
This error is displayed when the Printer has been left switched OFF for more than 31 days.
120xPrinthead Drive IC Error
The Piezo Drive IC on a Printhead is too hot (85C or higher) or too low (- 10C or lower).
121xPrinthead Temperature Error
The Printhead temperature is too high (85C or higher) or too low (-10C or lower). x = 0: Printhead Number 1 (Black). x = 1: Printhead Number 2 (Light Magenta). x = 2: Printhead Number 3 (Light Cyan). x = 3: Printhead Number 4 (Yellow). x = 4: Printhead Number 5 (Magenta). x = 5: Printhead Number 6 (Cyan).
1220Edge Sensor Error
The Printer has problems detecting the edge of the Media.
123xSub-Tank Sensor Error (Full or Half)
The Full and Half Sensors on the Sub-Tanks are defective. x = 0: Printhead Number 1 (Black). x = 1: Printhead Number 2 (Light Magenta). x = 2: Printhead Number 3 (Light Cyan). x = 3: Printhead Number 4 (Yellow). x = 4: Printhead Number 5 (Magenta). x = 5: Printhead Number 6 (Cyan).
124xInk Supply Sensor Error
The Ink Supply Sensor does not change even though the specified time has passed after driving the Ink Supply Motor for the Sub-Tank. x = 0: Printhead Number 1 (Black). x = 1: Printhead Number 2 (Light Magenta). x = 2: Printhead Number 3 (Light Cyan). x = 3: Printhead Number 4 (Yellow). x = 4: Printhead Number 5 (Magenta). x = 5: Printhead Number 6 (Cyan).
125xSub-Tank Supply Error
The Sub-Tank Sensor does not switch to less than half even though ink has been consumed. x = 0: Printhead Number 1 (Black). x = 1: Printhead Number 2 (Light Magenta). x = 2: Printhead Number 3 (Light Cyan). x = 3: Printhead Number 4 (Yellow). x = 4: Printhead Number 5 (Magenta). x = 5: Printhead Number 6 (Cyan).
126xTrailing Cable Connection Error
The Trailing Cable connected to the one of the following connectors is faulty. x = 0: Connector 9. x = 1: Connector 10. x = 2: Connector 11. x = 3: Connector 12.
1270Feed Motor Error
Over-current problem in the Feed Motor Drive Circuit.
1280Take-Up-Reel Motor Error
Over-current problem in the Take-Up-Reel Motor Drive Circuit.
1290End of Life of Part Reached
The end of life of the Prime Assembly has been reached since it has been working for more than 58 hours.
170XServo Motor Error
The Paper-Axis or the Scan-Axis Motor moves the Carriage, but the input from the Linear Encoder Sensor does not change. x = 0: Feed System. x = 1: Carriage System. x = 2: Servo Unit.
2000Add-On (HEB2) Control PCA
Problems with the Add-On (HEB2) Control PCA detected.
4000Cap Position Adjustment Value
This error appears when the Cap Position Adjustment Value is set to zero.
F_es: 0001Operation Code Exception
F_es: 0002Slot Illegal Exception
F_es: 0003Address Exception
F_es: 0004DMA Error
F_es: 0005NMI Occurrence (WatchDog Error)
H01System Error
Abnormal operation of the Heater Relay Assembly.
H02Relay Board Error
The Heater Board and the Relay Board are not connected together.
H03Front Heater Temperature Error
Temperature read by the Front Heater is abnormal (lower than -10C or higher than 70C).
H04Rear Heater Temperature Error
Temperature read by the Rear Heater is abnormal (lower than -10C or higher than 70C).
H05Center Heater Temperature Error
Temperature read by the Center Heater is abnormal (lower than -10C or higher than 70C).
H06Front Heater Time-out Error
The temperature of the Front Heater does not reach the preset temperature even after 15 minutes.
H07Rear Heater Time-out Error
The temperature of the Rear Heater does not reach the preset temperature even after 15 minutes.
H08Center Heater Time-out Error
The temperature of the Center Heater does not reach the preset temperature even after 15 minutes.
H09Operation Panel Switch Error
The specified switch is not pressed for 30 seconds or more when the diagnostics that verifies the switch action is executed.
H10Zero Cross Error
This error occurs when the diagnostics for the AC Relay is executed.

Наверх
  • Яндекс.Метрика
    Создание интернет-магазина Andyshop.ru - PHPShop. Все права защищены © 2004-2024.