| Code | Description |
| 1010 | ATG/RSM Loading Error The program load from the Flash ROM on the Main PCA to the ASIC on the Main PCA or sum-check was not performed correctly and an error occurred. |
| 1011 | PTC/PDD Loading Error The program load from the Flash ROM on the Main PCA to the ASIC on the Carriage PCA or sum-check was not performed correctly and an error occurred. |
| 1100 | Flash ROM Error The program area in the Flash ROM is sum-checked, and it could not be read, causing an error. |
| 1101 | ATG/RSM Error The read/write of the ATG/RSM registers and RSM Mask Memory Data on the Main PCA was diagnosed and an error was detected. |
| 1102 | Trailing Cable Error The Trailing Cable between the Main PCA and the Carriage PCA is not connected. |
| 1103 | Heater Relay Board Connection Error The Cable between the Main PCA and the Heater Relay Board is not connected. |
| 1104 | ISS PCA Connection Error The Cable between the Main PCA and the ISS PCA is not connected. |
| 1105 | PTC/PDD Error The PTC/PDD registers cannot be read or written correctly. |
| 1106 | Power Error The power supplies of +36, +24 and +12 V were diagnosed and could not be detected. This error is checked when the Printer is booted up. |
| 1107 | Carriage Interface Error The Carriage Interface is not connect correctly. |
| 1108 | USB Error USB communication is not performed correctly. |
| 1109 | EEPROM Error The parameters saved in the EEPROM on the Main PCA cannot be read correctly. |
| 110A | Band Memory Error The read/write of the SDRAM (band memory) on the Main PCA was diagnosed and an error was detected. |
| 110B | Cap Horizontal Position Error The Cap horizontal position is defined as 0.0 mm. |
| 1110 | Data Path Time-out Error The data transfer via USB from the host does not finish even when a specified time period has passed. |
| 112x | Vacuum Fan Error. x = 0: The Vacuum Fan 1 (extreme right of the printer) has failed. x = 1: The Vacuum Fan 2 (center right of the printer) has failed. x = 2: The Vacuum Fan 3 (center left of the printer) has failed. x = 3: The Vacuum Fan 4 (extreme left of the printer) has failed. |
| 1130 | DMA Controller Error. An error occurs when the DMA of the printing data cannot be completed. |
| 1140 | Flash ROM Write Error A time-out error occurs when the flash ROM contents are being saved and erasing does not end. |
| 1150 | Home Position Sensor Error The Carriage cannot be moved to it’s home position. |
| 1160 | Wiping Error When the Wiping Motor has been running for a while, the sensor fails to detect that the Motor has made one turn. |
| 1170 | Temperature Sensor Error The Temperature Sensor detects abnormal temperatures (-10C or lower or 85C or higher). |
| 1180 | Pump/Wipe Motor Error Over current is detected in the pump/wipe motor drive circuit. |
| 119x | Printhead Drive Voltage Error The Printhead drive voltages generated on the Carriage PCA do not reach the expected values. |
| 11A0 | EEPROM I/O Error The read/write of the EEPROM on the Main PCA was diagnosed and an error was detected. |
| 11D0 | Printhead Cooling Fan Error The Printhead temperature does not drop even after the printhead Cooling Fan rotates for more than a specified time. |
| 1,10E+01 | Long Term Storage Error This error is displayed when the Printer has been left switched OFF for more than 31 days. |
| 120x | Printhead Drive IC Error The Piezo Drive IC on a Printhead is either too hot (85C or higher) or too low (-10C or lower). |
| 1220 | Line Sensor Error The Printer has problems detecting the edge of the Media. |
| 126x | Trailing Cable Connection Error The Trailing Cable connected to the one of the following connectors on the Carriage PCA is faulty. x = 0: Connector 9. x = 1: Connector 10. x = 2: Connector 11. x = 3: Connector 12. |
| 1290 | End of Life of Part Reached The end of life of the Prime Assembly has been reached since it has been working for more than 43 hours. |
| 1310 | Cap Sensor Error The cap home position cannot be found. |
| 1320 | Scan-Axis Motor Heating Error The Scan-Axis Motor Temperature Sensor has detected a temperature over 100C |
| 1330 | Scan-Axis Motor Temperature Sensor Error The Scan-Axis Motor Temperature Sensor has detected abnormal temperatures (-22.5C or lower or 150C or higher). |
| 140x | Heater Temperature Error Temperature read by the Heater Temperature Sensor is abnormal (lower than -20C or higher than 200C). x = 1: Front heater. x = 2: Center Platen. x = 3: Rear Heater. |
| 141x | Heater Error (High Temperature) Temperature read by the Heater Temperature Sensor is above 65C). x = 1: Front heater. x = 2: Center Platen. x = 3: Rear Heater. |
| 143x | Heater Error (Insufficient Heating) The Heater is not heated to a specified temperature even after 30 minutes have passed. x = 1: Front heater. x = 2: Center Platen. x = 3: Rear Heater. |
| 144x | Heater Error No heater sequence interrupt. |
| 2000 ... 6000 | Firmware Logic Error A logic error has occurred in the Firmware program. |
Картриджи принтера
Заправка картриджей
Ремонт принтера
Запчасти принтера
