| Code | Description |
| 0000D8 | External Library Error. |
| 10020 | Firmware DIMM Test failure. |
| 10021 | Memory DRAM DIMM Test failure. |
| 10023 | EEROM Test failure. |
| 01002D | The Main PCA cannot communicate with the Carriage. |
| 10040 | Error in Paper-axis Encoder quadrature. |
| 10041 | Error in Scan-axis Encoder quadrature. |
| 10042 | Error in Service Station-axis Encoder quadrature. |
| 10050 | PostScript Processing Error. |
| 01009X | Error in Paper-axis Motor Encoder |
| 02xxxx | PostScript/Firmware Error. |
| 048xxx | The EIO card is from a third party vendor and may not be fully compliant with the IIO Protocol specification 2.0 OR the EIO Card firmware is not updated. |
| 04Cxxx | EIO Accessories (EIO Card/Hard Disk Drive) Error. |
| 60301 | One of the Printheads has an Internal Electrical Problem. |
| 60305 | Thermal Shutdown error (one of the Printheads has gone above the maximum Temperature). 00000000 - Cyan Printhead Failed. 00000001 - Magenta Printhead Failed. 00000002 - Yellow Printhead Failed. 00000003 - Black Printhead Failed. |
| 60309 | Problem with setting the Voltage of the Printheads. |
| 06030A | Error in finding the Mark Encoder. |
| 06030B | The Ambient Temperature measured is out of the normal range. |
| 70100 | Firmware Error. |
| 80001 | PostScript Error. |
| 09xxxx | EIO Accessories (EIO Card/Hard Disk Drive) Error. |
| 0A0000 | The Air Pressure is below the minimum requirement. |
| 0A0010 | Problem in Pressurizing the Air System. |
| 0A0020 | Error in Calibrating the APS Sensor. |
| 0A0030 | Problem in Depressurizing Air System. |
| 0A0040 | Ink Tubes Initialization Failure Due to Low Air Pressure. |
| 0A0050 | The Printer has detected a leak in the Tubes System before the life of the System. |
| 0A0060 | The Printer has detected a leak in the Tubes System after the life of the System. |
| 0A0070 | The Backup EEROM contents stored in the Tubes System are not consistent with the ones required by the firmware. |
| 0B0000 | Bad Ambient Temperature measured. |
| 0B0001 | Bad Humidity read. |
| 0B0002 | Bad IDS pressure read. |
| 0B0003 | ADC0 Internal channels check Failure. |
| 0B0004 | Unable to detect Pump. |
| 0B0005 | Unable to detect Valve. |
| 0B0006 | The Trailing Cable has been incorrectly connected OR the fuse in the Electronics Module has been burned. |
| 0B0007 | Unable to detect Vacuum Fan. |
| 0B0008 | Unable to detect Cooling Fan. |
| 0B0009 | Unable to detect Aerosol Fan (Included on the Right Cover). |
| 0B000A | Primer Shutdown Error. |
| 0B000B | Pump or Pressure Sensor not working. |
| 0B000C | Serial Device ADC test failure |
| 0B000D | 24 V source test failure. |
| 0C0030 | Bad Drop Detector. |
| 0C0032 | Drop Detector not Calibrated for all Printheads. |
| 0C1000 | Primer not Calibrated. |
| 0C1001 | Primer Shutdown Error. |
Картриджи принтера
Заправка картриджей
Ремонт принтера
Запчасти принтера
